ow Galleto 2 Fgtech works?

by **dadal** » Sat Jan 03, 2015 1:35 am

pin 28 of 29f200bb connected to massa of PCB ecu (through a resistor 8-10 Kom) or to gray wire of galletto.
Good luck

Thank you wery much,
I have tried it today, but no success
I have first 28 pin of flash eprom connected to the gray cable( with and without resistor),
...later to the massa of pcb
...and then to the black wire of Galetto
no one successfully
here's the pictures
I did not understand this message, " apply power toe the dashboard and remove ground to pin 28 of flash eprom end to continue,"
first in the manual say pin 28 must be connected to massa and now say REMOVE.. I have nothing removed, pin 28 stays connected to massa or gray wire.
http://s27.postimg.org/ef3ic68g3/error.png http://s9.postimg.org/lfj201ef3/error1.png

by **2xded** » Sat Jan 03, 2015 1:01 pm

Hi!
What do not you understand?
Do as it is written in the first picture http://s27.postimg.org/ef3ic68g3/error.png
1.Remowe power.
2.Groud pin 28 of the flash eprom (through a resistor 8-10 Kom).
3.Apply power.
4.Remowe ground to pin 28.
5.press "ECU Data" or "Read File".
Good luck.

by **dadal** » Sat Jan 03, 2015 4:28 pm

2xded wrote:Hi!
What do not you understand?
4.Remowe ground to pin 28.
Good luck.

Hi 2exded,
1.Remowe power.----> OK
2.Groud pin 28 of the flash eprom (through a resistor 8-10 Kom).----> pin28 is connected to Gray wire ( or massa of pcb)
3.Apply power.----> OK
4.Remowe ground to pin 28-----> I do not understand this, First I must to pin 28 throught a resistor connect to ground, and now I have to remove it again? if I remove pin 28,then galletto have no more connection with ecu ???? ,,

5.press "ECU Data" or "Read File".------- OK ...then I have error message

Thanks for your interest,

by **2xded** » Sat Jan 03, 2015 5:17 pm

pin 28 of 29f200bb !
Ground connection to pin 28 for transfer processor in BSL mode.
Play time connection to the ground on the 28th pin after power up.
Good luck.

by **dadal** » Sat Jan 03, 2015 8:30 pm

2xded wrote:pin 28 of 29f200bb !
Ground connection to pin 28 for transfer processor in BSL mode.
.
Good luck.

Hi 2exded,
I understand it now, Play time connection to the ground on the 28th pin after power up I did it not "after" power up, wel before power up..

thank you very much :thumbup:

by **2xded** » Sun Jan 04, 2015 8:47 am

Hi!
after power up by switch http://image.dhgate.com/albu_251909863_00-1.0x0/promotion-fgtech-galletto-2-master-obd2-fgtech.jpg
Regards.

by **dadal** » Tue Jan 06, 2015 10:25 pm

can anyone tell me what the following terms mean ( in the manual of galletto 2) ?
internal - external flash ?
Bootmode - Flasher - Bootmode - Bootmode tricore ?

see picteres .

and which cars I can read bij OBD2 socket with the supplied cable
have somebay a list ?
this cable :
http://www.obdtool.co.uk/upload/temp/images/fgtech-galletto-4-obd2-connection.jpg