Hi!

Please someone help me to foud a map pack for winols, to my ECU (EDC15C2 Citroen Xantia 90hp HDI Manu al)
I'd like to found configuration switches, and maps for MAP, MAF, EGR, BOOST control, SUSPENSION control switch.
At this moment i have a fixed geometry turbo without intercooler.
In the future i'm planning to replace it with a variable geometry turbo controlled with EGR vacuum solenoid, and also add an intercooler.

Here is my mappack for Picasso. Offset for second bank is 10000

Address;Name;Size
$6888A;"SOI; INJ Carto. base HE start with VE Angle = f (N M_EMOT)";"16x16"
$61CC4;"ARF Cartographie principale-Valeur consigne M_L = f(N M_E)";"16x16"
$665B4;"Torque limiter 2";"6x1"
$65548;"Torque limit; BEG Torque limitation M_E = f (N)";"19x1"
$66DC6;"rail pressure precontrol RPC Carto. limit valve. press.rail RCO = f (T_eau P_rail)";"8x8"
$68FAA;"Duration INJ AD 1. Carto Injecteur [us] = f(P_RAIL ME)";"20x16"
$6437E;"Boost limit by T turbo; Limitation val. LD setpoint according to LTF n";"10x8"
$62D6A;"Boost Pressure correction curve for smoke limitation PLB Cartogr.correct.pression sural. P_aircorr. = f(P_air T_air)";"10x10"
$64ADE;"Boost limit by AP; Valeur maxi = f( P_ATM n )";"10x10"
$6486C;"N75; LDR carto de correction = f( P_ATM M_E ) pour pilotage";"9x9"
$64700;"N75; LDR carto de pilotage mode eco P_L = f(N M_E)";"10x16"
$64CC2;"Boost rqst; LDR carto de base mode eco P_L = f(N M_E)";"10x16"
$64E3E;"Boost rqst; LDR carto de base mode sport P_L = f(N M_E)";"10x16"
$64FDA;"EXT Swirl Rapport cyclique correction d'air addit.";"6x6"
$65224;"IQ limit fuel T; EXT flow limitation in case temp. high fuel sensor on the return";"4x8"
$65FC4;"DW; KF driving approval fgm_VzuN> Threshold";"6x8"
$66048;"DW; KF driving approval fgm_VzuN> Threshold";"6x8"
$67262;"Rail press limit; RPC Max pressure function of N; Pmax = f (n M_EAKT)";"8x16"
$66E62;"Rail press; RPC Carto.base Press.rail cons. P_rail = f(N M_EMOT)";"16x16"
$668A2;"STA Basic Start Charts M_E = f (N T_water)";"10x8"
$655B6;"Smoke map; BEG Fume limitation mapping M_E = f (N M_L)";"16x16"
$657D6;"BEG Carto anti-ebullition M_E = f(T_W V)";"6x6"
$6584C;"BEG Incr. flow at water temperature M_E = f (N T_water)";"9x10"
$65948;"MAP limit; BEG Fume limitation mapping M_E = f (N P_aircorr.)";"16x16"
$65D3A;"Torque limiter; BEG Flow limitation curve (system fault) M_E = f (N)";"12x1"
$65DC2;"Inverse DW; Reverse mapping of agrem.conduite - PWGinv. = f (N M_E)";"10x10"
$65EF0;"IQ limit fuel T;BEG Flow limitation according to T-diesel";"4x8"
$68CDA;"Duration INJ AD 1. Carto Injecteur [us] = f(P_RAIL ME)";"20x16"
$6494A;"LDR carto de pilotage mode sport P_L = f(N M_E)";"10x16"
$62EB2;"MAP to MAF; Masse d'air-VGW-KF M_L = f(N P)";"6x6"
$67BC0;"Soi limiter INJ Carto. corr. Debut de commande HE temp. d'air Angle = f(N M_EMOT)";"16x8"
$62138;"RPC changement SHUT_OFF > WAIT_FOR_EVER";"1x1"
$62136;"RPC changement WAIT FOR_EVER > SHUT_OFF";"1x1"
$6219A;"RPC Difference max. the press.rail unfiltered / filtered";"1x1"
$62190;"CPP Threshold of the press. max. rail for surveillance";"1x1"
$62152;"RPC KDF: threshold pressure for F2 must be smaller than zuwPKmax";"1x1"
$6215E;"RPC min loop offset for DT1";"1x1"
$677B4;"SVBL Regul.pres.sural. Upper limit absolute of the set point";"1x1"
$61115;"EGR Commut. fonc. avec/sans (1/0) recycl. gaz d'echap.";"1x1"
$6111C;"Commut. fonc. Commande EGR avec / sans (1/0) hysteresis";"1x1"

Thankyou :)
Do someone have info, why i was unable to read AM29F400BT(SO44) with TNM5000 EEPROM programmer?