Maps needed for tuning EDC15C2

by **stanleybg** » Fri Sep 12, 2014 10:37 am

Thank you for your help.God bless you :) :thumbup:

by **andreqn** » Sun Sep 14, 2014 9:22 pm

great!!!!

by **stanleybg** » Wed Sep 24, 2014 9:04 pm

Can you help me to find Rail Pressure Limiter in this bin file.I found where the bits are 6000 , 6000 , 6000 , 13500 , 13500 but where is the start of the map.I can't find x and y axis.
I understood that the rail pressure and soi uses the same x,y axis.And may be this map uses shared x,y axis ?

by **Vasily_U** » Thu Sep 25, 2014 12:23 pm

stanleybg wrote:Can you help me to find Rail Pressure Limiter in this bin file.I found where the bits are 6000 , 6000 , 6000 , 13500 , 13500 but where is the start of the map.I can't find x and y axis.
I understood that the rail pressure and soi uses the same x,y axis.And may be this map uses shared x,y axis ?

Rail Pressure Limiter map

406 sedan niki_rpl.rar

by **Vasily_U** » Thu Sep 25, 2014 1:22 pm

Vasily_U wrote:Rail Pressure Limiter map

I can not edit the previos post, write a new one.

406 sedan niki_rpl.rar

by **stanleybg** » Thu Sep 25, 2014 8:24 pm

Thank you for your help.Strange think is I alreday had found and identifyed these maps.I was not sure in my skills.You remember my previous post that you opened "ORIGINAL FILE MY CAR" I tryed find these Rail Limiter Maps there , but what i found is Rail Limiter Map size 6x14 ? Is that allright.As i read for the maps of EDC15 it should be 8x16.Is this normal.

by **Vasily_U** » Thu Sep 25, 2014 9:24 pm

stanleybg wrote:Thank you for your help.Strange think is I alreday had found and identifyed these maps.I was not sure in my skills.You remember my previous post that you opened "ORIGINAL FILE MY CAR" I tryed find these Rail Limiter Maps there , but what i found is Rail Limiter Map size 6x14 ? Is that allright.As i read for the maps of EDC15 it should be 8x16.Is this normal.

I dont know why, but Rail Limiter Map realy have size 6x14 :crazy:

by **stanleybg** » Thu Sep 25, 2014 9:32 pm

Hahaha. Thank you for your answer.Now i know that somethink is :crazy: and the map is 6x14.
Thank you for your time with my learning :thumbup:

by **manekin13** » Sat Sep 27, 2014 2:56 pm

Hey, I have two questions about HDI.
1.Could You explain me why on the full throttle on the first and second gear fuel quantity is smaller then on the higher gears? I see it in logs of my C5 2.0 HDI. Mainly on the first gear. First gear torque limiter is original set to 100 mm3. Maybe it is not enough air on that gears?
2. I compared 2.0 HDI rail pressure map with rail pressure map of alfa 1.9 jtd 105 and rail pressure of HDI in the middle iq area is much lower( sometimes 150 bar difference). Do You know why it is rail pressure on cruising area on HDI so low? 1.9 jtd seems to be less fuel consuming according to people reports. Could it be according of higher fuel pressure?

by **leonevich** » Sat Sep 27, 2014 9:05 pm

manekin13 wrote:Hey, I have two questions about HDI.
1.Could You explain me why on the full throttle on the first and second gear fuel quantity is smaller then on the higher gears? I see it in logs of my C5 2.0 HDI. Mainly on the first gear. First gear torque limiter is original set to 100 mm3. Maybe it is not enough air on that gears?

If I understand correctly, then the first and second gear, the turbine not enough time to enter the value of the boost. Check the turbo maps, N75 maps and look smoke map.