Siemens SID and Galleto 1260

by **tomik1987** » Sun May 19, 2013 1:33 pm

Self cable and soft Galleto 1260, to today, I met only with EDC15C2 bosch ones can do just fine. But today I had a Siemens SID 801 Galleto load your controller but when I wanted to download a file. thrown error. Can you help? advice?

by **julianstefanov** » Sun May 19, 2013 1:50 pm

This is not a error. It's a normal message which you must follow to read the ECU.
You must enter the ECU in BOOT Mode, then you can read it with galletto.

by **tomik1987** » Sun May 19, 2013 2:22 pm

how exactly do I enter in ECU boot mode? I do it in the program? Galleto 1260??

by **julianstefanov** » Sun May 19, 2013 4:29 pm

You must do the following:

1. Open the ECU (be carefull)
2. Find the EEPROM 29F400 inside (it's on the picture)
3. Solder a cable on pin 28 (like on the picture)
4. Put that cable to your car GND (gnd on the battery)
5. Put your key on position 2 (ignition on) - DO NOT start the engine!!!
6. Connect Galletto to the OBDII port and read the ECU
7. Disconnect Galletto
8. Disconnect the cable from 28 pin and remove it totaly
9. Close the ECU
10. DONE

Now you'll have the EEPROM DUMP and you can edit/modify and then WRITE BACK to the ECU as many times as you want without any cables or opening the ECU. Just 1st time when you have to read the EEPROM, you must use the steps from 1 to 10.

If something is not clear, let me know.

Regards
Julian

by **ominimicu** » Wed May 22, 2013 5:31 pm

are u sure galletto will read that????

by **julianstefanov** » Sun Jun 02, 2013 7:22 pm

Ofc I'm 1000% sure. :)

by **BrunoC** » Wed Sep 11, 2013 12:15 am

siemens sid 806 run the same way, ie connecting the pin 28 to mass?
the pin is the next picture?

http://youyoukiller.free.fr/boot_mode/p ... 06%201.jpg

is it safe?

Thank you for everything.

by **Rocknsock** » Mon Apr 13, 2015 9:35 pm

I need that information too, about sid 806!

by **mo_ferwana** » Tue Apr 14, 2015 10:30 am

ominimicu wrote:are u sure galletto will read that????

Hi
Yes I am sure it can

by **Rocknsock** » Tue Apr 14, 2015 12:18 pm

julianstefanov wrote:You must do the following:

1. Open the ECU (be carefull)
2. Find the EEPROM 29F400 inside (it's on the picture)
3. Solder a cable on pin 28 (like on the picture)
4. Put that cable to your car GND (gnd on the battery)
5. Put your key on position 2 (ignition on) - DO NOT start the engine!!!
6. Connect Galletto to the OBDII port and read the ECU
7. Disconnect Galletto
8. Disconnect the cable from 28 pin and remove it totaly
9. Close the ECU
10. DONE

Now you'll have the EEPROM DUMP and you can edit/modify and then WRITE BACK to the ECU as many times as you want without any cables or opening the ECU. Just 1st time when you have to read the EEPROM, you must use the steps from 1 to 10.

If something is not clear, let me know.

Regards
Julian