Maybe not a bad idea to share.

CANtieCAR v3.x Bluetooth + USB - ALL IN ONE. Diagnostic tool and flasher in one. Original tool!

For all that are sick and tired of cheep devices and a large number
of different OBD cables/devices here is one very great ORIGINAL/GENUINE device that simulates
quite a nice number of different devices.

It has built-in solid state relays multiplexer and very stable running.
You can get rid off numbers of cables and use only one. It can be used also for BDM.

Here is a list of supported - emulated adapters.

Emulated well-known adapters
- USB-Serial (6:CTS, 7:RXD, 8:DTR/DSR, 14:RTS, 15:TXD)
- KL-Line (7:K, 15:L)
- 2K-Line (7:K, 15:K2)
- KKL-Line (7:K, 15:L/K2)
- 3K-Line (7:K, 15:K2, 8:K3)
- OPEL 4K-Line (7:K, 8:K3, 3:K4, 12:K5)
- Multiplexed K-Line to ALL OBD-pins
- VAGCOM v409-1 (KKL-Design)
- RS485 Duplex (12:A, 13:B)
- RS485 Half-Duplex (12:A, 13:B)
- Carsoft BMW 6.5/7.3
- Carsoft MB 7.4
- Carsoft MB 7.4 - OBDII
- Siemens Airbag 3.0
- NISSAN Consult I + Sync (10:TX, 2:RX, 7:SYNC)
- NISSAN Consult I - OBDII (12:TX, 13:RX)
- DIESEL-kit v1.0 Bluetooth ready
- VOLVO 9998555
- P.A.Soft BMW Scanner v1.2.5
- P.A.Soft BMW Scanner v1.3.6
- P.A.Soft BMW Scanner v1.4.0 Demo
- P.A.Soft BMW Scanner v1.4.x
- BMW EDIABAS: STD:OBD
- BMW EDIABAS: ADS
- BMW EDIABAS: D-CAN Combo (STD:OBD K + D-CAN)
- BMW EDIABAS: D-CAN Fast (STD:OBD D-CAN) Bluetooth ready
- BMW EDIABAS: D-CAN Fxx (STD:OBD D-CAN for F-series) Bluetooth ready
- BMW EDIABAS: JBE PT-CAN (STD:OBD + JBE CAN 500k) Bluetooth ready
- BMW EDIABAS: JBE K-CAN (STD:OBD + JBE CAN 100k) Bluetooth ready
- ELM323 v2.0+ Bluetooth ready
- ELM327 v1.4+ Bluetooth ready
- ELM327 v1.4+ (ScanTool.net) Bluetooth ready
- DigiProg OBDII Flasher
- KWP2000 Flasher
- KWP2000 PLUS Flasher
- CMD EDC16 OBDII Flasher v1236 - K-Line
- CMD EDC16 OBDII Flasher v1244 - K-Line
- CMD EDC16 OBDII Flasher v1251 - CAN
- CMD EDC16 OBDII Flasher v1255 - K-Line
- CMD MAP3Diag
- CMD MPC5xx BDM Programmer v1251 (4/5:GND-6, 6:RST-1, 7:DI-7, 8:SCK-5, 14:IGN-2, 15:DO-8, 16:PWR-9)
- Galletto v1050/1080 EOBDII Flasher
- Galletto v1245 EOBDII Flasher
- Galletto v1250 EOBDII Flasher
- Galletto v1260 EOBDII Flasher
- VAG K+CAN Commander v1.4/v2.5/v3.6
- LICZNIK USB Dongle for v4.8a
- Lawicel CAN232 v3 (6:High, 14:Low) Bluetooth ready
- Lawicel CANUSB v1 (6:High, 14:Low)
- PonyProg2000 (4/5:GND-10, 6:IN#-6, 7:OUT#-5, 8:SCLK#-4, 14:VCC/RST-1/3, 15:RST#-2)
- EDiTH Eberspacher ISO Adapter
- OpenPort v1
- OpenPort v1.2
- OpenPort v1.3 Universal (11:Vpp/Boot)
- MultiECUScan Bluetooth ready
- PassThru SAE J2534-1/2 Bluetooth ready
- PassThru SAE J2534-1/2 - BMW up to 2008 Bluetooth ready

Hardware
- Powerful ARM-core MCU
- Bluetooth v2.0 + EDR Bluetooth ready
- True USB-ready device: CDC, FT232B/R-emulation, FT2232C-emulation, MSD over SD Card
- SD Card: internal Flash storage with USB-MSD up to 32GB
- 3 independent ISO9141/ISO14239 K-Lines (ISO-Lines): OBDII-pins 7,8,15
- 2 multi-functional lines (MFLs): CAN - one and two-wires, K Lines, J1850, DC-DC-out (5-30V)/1W etc.
- built-in solid state relays multiplexer for OBDII-pins 1,2,3,6,8,13 and 8,9,10,11,12,14
- built-in hardware UART multiplexer
- built-in switchable CAN-bus differential terminator 120 Ohm
- 11 Leds: 6 - Bus Activity, 1 - USB/Bluetooth TX Activity, 1 bi-color - Power state: USB and car + USB Activity, 1 - Bluetooth Status/Activity, 2 - Status
- 2 DC-DC: 5V/500mA and programmable (5-30V)/1W
- 8 ADC Channels: Power ISO-Lines, Power MFL, High MFL, Low MFL, OBD:1, OBD:8, OBD:9, OBD:16
- Systems: Up to 32V
- Speed: ISO-Lines up to 500kbit/s; CAN up to 1Mbit/s
- Special OBDII-connector design
- Security Firmware updates
- ALL protections with Resetable fuses
- Support additional equipment for cars

I have this tools and use it only for Multiecuscan. I have VIP vesion and I can use all emulations. But real these are really old cheap adapters. Support for using emulations is non-existent. It takes a lot of experience to be all set.
And the price is too high for the ful version. Sincerely hardware is excellent

Hello everyone. I recently purchased this interface (for two weeks), interests me more as a diagnostic, for now I could make it work with honda, toyota, multiecuscan, rheingold, consult III, dtt2000, odis. The consult him I have to try just entering a car brand nissan workshop. Does anyone have more experience with this diagnosis? Can you give me some advice on what works yet.
Thank you for your intervention.
Nello

How does this work? Is there a link to purchase? This seems very handy!

Super device!

hello friend where i can buy this tool ?thanks

hello friends I have purchased the cantiecar with license multiecuscan.Voglio ask if someone uses it with mb carsoft or with digiprog !!!