e60 530d 218ps stage 1

by **Kisu1337** » Wed Feb 12, 2020 10:30 pm

Hello, i am trying to make stage 1.

What is wrong and why i can't get more power ? Only little bit smoke at high revs.

e60 stage 1 v4.bin

by **NRT** » Thu Feb 13, 2020 12:46 pm

Kisu1337 wrote:Hello, i am trying to make stage 1.

What is wrong and why i can't get more power ? Only little bit smoke at high revs.

e60 stage 1 v4.bin

post your ori file too

by **Kisu1337** » Thu Feb 13, 2020 7:12 pm

NRT wrote:
Kisu1337 wrote:Hello, i am trying to make stage 1.

What is wrong and why i can't get more power ? Only little bit smoke at high revs.

e60 stage 1 v4.bin

post your ori file too

Ori File:

BMW E60 530d 218ps original.bin

by **adamek** » Wed Feb 19, 2020 2:34 pm

check your SVBL ,adress - E4CB2 .its still 2350mbar.

by **adriancl** » Wed Feb 19, 2020 4:07 pm

Hi mate,
wrong tuned file.Of course no power gain, because except the SVBL, your IQ is stock.That because you didn't touch Lambda maps.Also on Nm/IQ map you confused the X axis with map value,you defined wrong the map address.
You didn't touch IQ limiters maps.
Your rail pressure limiters have not been completely modified.
You not modified the SVIQ
You moded one map no need to touch regarding air mass.
And so on.
Anyway the big mistake is you used percent tuning,no calculation, nothing, nothing.
It is shameful as one of the best diesel engines ever built is forced to turn with such a bad software.
Please do not hate me, I only try to help you.

by **Kisu1337** » Thu Feb 20, 2020 8:34 am

adamek wrote:check your SVBL ,adress - E4CB2 .its still 2350mbar.

Thank You.

adriancl wrote:Hi mate,
wrong tuned file.Of course no power gain, because except the SVBL, your IQ is stock.That because you didn't touch Lambda maps.Also on Nm/IQ map you confused the X axis with map value,you defined wrong the map address.
You didn't touch IQ limiters maps.
Your rail pressure limiters have not been completely modified.
You not modified the SVIQ
You moded one map no need to touch regarding air mass.
And so on.
Anyway the big mistake is you used percent tuning,no calculation, nothing, nothing.
It is shameful as one of the best diesel engines ever built is forced to turn with such a bad software.
Please do not hate me, I only try to help you.

I see, so much wrong. Thank You for reply and advices, looks like i have so small mappack for this ecu. Need to find more important maps. I will try to make it again with Your advices.

by **Kisu1337** » Sun Feb 23, 2020 12:27 pm

adriancl wrote:Hi mate,
wrong tuned file.Of course no power gain, because except the SVBL, your IQ is stock.That because you didn't touch Lambda maps.Also on Nm/IQ map you confused the X axis with map value,you defined wrong the map address.
You didn't touch IQ limiters maps.
Your rail pressure limiters have not been completely modified.
You not modified the SVIQ
You moded one map no need to touch regarding air mass.
And so on.
Anyway the big mistake is you used percent tuning,no calculation, nothing, nothing.
It is shameful as one of the best diesel engines ever built is forced to turn with such a bad software.
Please do not hate me, I only try to help you.

Updated a bit tune, fixed Nm/Iq map yea did mistake there, Edited SVBL a guy above posted, changed maps for linear percentage add instead full 10% change..., also can't find anything like SVIQ :thumbdown:

btw Why i have to tune Lampda Maps ? Its original at +-15AFR what i checked.

If anyone could check again ? and tell me more about it :D

530d 218ps stage 1 rev 1 372280.bin

by **Kisu1337** » Mon Feb 24, 2020 5:30 pm

Kisu1337 wrote:
adriancl wrote:Hi mate,
wrong tuned file.Of course no power gain, because except the SVBL, your IQ is stock.That because you didn't touch Lambda maps.Also on Nm/IQ map you confused the X axis with map value,you defined wrong the map address.
You didn't touch IQ limiters maps.
Your rail pressure limiters have not been completely modified.
You not modified the SVIQ
You moded one map no need to touch regarding air mass.
And so on.
Anyway the big mistake is you used percent tuning,no calculation, nothing, nothing.
It is shameful as one of the best diesel engines ever built is forced to turn with such a bad software.
Please do not hate me, I only try to help you.

Updated a bit tune, fixed Nm/Iq map yea did mistake there, Edited SVBL a guy above posted, changed maps for linear percentage add instead full 10% change..., also can't find anything like SVIQ :thumbdown:

btw Why i have to tune Lampda Maps ? Its original at +-15AFR what i checked.

If anyone could check again ? and tell me more about it :D

530d 218ps stage 1 rev 1 372280.bin

Hmm tested it today with Testo and got less smoke and boost at 1.5bar also Nm drops at higher revs no idea why Nm doesn't go more than 490 Any idea how to improve my file ?

530d test.png